|
Home Page >
Amplifiers >
AMP4CH-DF
| AMP4CH-DF -- click for tour |
 |
AMP4CH-DF Amplifier Features
• Amplifies four differential analog channels
• Gain of 100 standard
• Custom gains possible
• Adds almost no noise when amplifying
• Low 120 milliamp current draw
• Price $260 for In The Box bundled system
• Spec Table
• PDF Documents & Software
• Options
Download PDF Product Flyer 
Product Description
The AMP4CH-DF is a 4 channel amplifier for use with differential
inputs like those needed to drive the PAR4CH 24-bit
data acquisition system. In its standard configuration, the AMP4CH-DF
provides a gain of 100 on each analog input channel while using only
120 ma.
The AMP4CH-DF allows high resolution acquisition of very small
signals. With its standard x 100 gain, the AMP4CH-DF allows signals as
small as +/- 100 millivolt to span the full +/- 10 volt analog input
range of the PAR4CH. Designed with extremely good noise
characteristics, the AMP4CH-DF adds almost no detectable noise to the
final acquired data.
The AMP4CH-DF comes with all the accessories you need. These
include an enclosure that stacks nicely with the PAR4CH and the power
and D-shell cables for connecting to the PAR4CH. All you supply are
the analog inputs.
The gain on each channel is controlled by a resistor.
Soldering on a different resistor changes the gain. Custom gain
configurations are available for a small fee when placing your order.
Specifications Table
| AMP4CH-DF Specs |
| Channels: |
4 |
|
| Gain: |
Factor of 100 or 40 Db |
|
| Analog Input Type: |
Differential |
FAQ note |
| Analog Input Voltage: |
+/-100mv with gain of 100 and PAR4CH |
FAQ note |
| Analog Input Impedance: |
Resistor in parallel with high impedance
op amp input. Nominally 51K. |
FAQ note |
| Analog Input Header: |
15 pin D-Shell or plain wire with TRM15E |
|
| Analog Input Cable: |
Not supplied, twisted pair recommended |
FAQ note |
| Noise: |
Resolution, crosstalk and common mode
rejection of PAR4CH unchanged at an
amplifier gain of 100 |
FAQ note |
| PAR4CH Connection: |
15 pin D-Shell female-female cable and
2.1mm daisy chain power cable |
|
| Power Requirements: |
9 to 24 vdc or vac, 9 volts DC preferred, 120ma @+9v |
|
| Board Dimension: |
5.25" W x 6.00" D, same as PAR4CH |
|
| Enclosure Dimension: |
5.50" W x 1.63" H x 6.50" D |
|
| ROHS Compliance: |
Compilant by exemption |
FAQ note |
| Price: |
See "in the box" table below |
|
Documents and Software
These documents represent the complete specs for this product.
They can also be found on our
Downloads page.
| AMP4CH-DF Documents |
| Category |
Description |
Rev |
File |
# bytes |
| Product Flyer |
AMP4CH-DF specs |
2007/11/12 |
flyamp4chdf.pdf |
9,502 |
In The Box
When you purchase a AMP4CH-DF "in the box" system, the following are included:
| AMP4CH-DF In The Box |
| Item |
Description |
Price |
| BOARD-AMP4CH-DF |
Four channel amplifier with 100x gain |
$227 |
| CASE-AMP4CH-DF |
Vinyl coated steel enclosure with rubber feet |
$42 |
| CABLE-RIBBON15-FF |
5" DB15 female to female ribbon cable sends
amplified input to A/D |
$5 |
| CABLE-2.1-MM |
6" power cable with 2.1mm plugs on each end
for daisy chaining power |
$5 |
| CD-AMP4CH-DF |
CD with PDF user manual |
$1 |
| |
Total cost of individual items |
$280 |
| |
"In the box" discount
( box contents photo ) |
- $20 |
| AMP4CH-DF |
List price (credit card purchase) |
$260 |
| AMP4CH-DF |
Cash price (4% discount for cash/prepay/NET 30) |
$250 |
Options
Some users may want to consider these additional options:
| AMP4CH-DF Options |
| Item |
Description |
Price |
TRANS-WALL-09V-DC
TRANS-EURO-09V-DC |
9 vdc wall transformer (US 110 or Euro 220 vac) for powering the
AMP4CH-DF separately rather than daisy chaining with the PARxCH |
$16
$16 |
| AMP4CH-CHANGE-GAIN |
Install custom gain resistors on each AMP4CH-DF channel.
Contact customer support for the available values. |
$21 |
|
